AIW Radeon 32 meg OEM and XP: HELP!!!
Ok I did a fresh install of XP and installed the latest XP drivers off this site and also the 7. 2 media center. If I tryo to run 3dmark2000 I eiether get a black screen and have to reboot or I get a graphically messed up screen and lockup and have to reboot.
Ok I did a fresh install of XP and installed the latest XP drivers off this site and also the 7.2 media center.
If I tryo to run 3dmark2000 I eiether get a black screen and have to reboot or I get a graphically messed up screen and lockup and have to reboot. HELP please. I have agp4x on in my bios and my T-bird 1 gig is at 1.4 but this worked fine for my previous card.
my card is a OEM ATI AIW Radeon 32 meg DDR agp so its not a 8500. I am using the 6.13.3276 drivers off this site and ATIs. Also if I clock down to 1333mhz and install reference drivers from ATIs site, I can play max Payne (but get little red dot artifacts all over the screen) but 3dmark2000 and 2001 both crash to desktop or lock. Please help me I want use this card. What I dont understand is that I have a Matrox G550 before and could run my system at 140x10.0=1400mhz and agp4x and no problems
Ok its almost like the card is overheating but when i touch the heatsink on the card its cool. After running 3dmark2000 for about a minute I stat getting little artifacts all over the screen. and then i get kicked to the desktop and my whole screen gets distorted. Now i am at 1333 mhz right now. it makes no sense that the card is so wimpy that I have to run my t-bird at stock 1 gig, and every other card I have ever used I could run it at 1.4 (140x10) any ideas
If I tryo to run 3dmark2000 I eiether get a black screen and have to reboot or I get a graphically messed up screen and lockup and have to reboot. HELP please. I have agp4x on in my bios and my T-bird 1 gig is at 1.4 but this worked fine for my previous card.
my card is a OEM ATI AIW Radeon 32 meg DDR agp so its not a 8500. I am using the 6.13.3276 drivers off this site and ATIs. Also if I clock down to 1333mhz and install reference drivers from ATIs site, I can play max Payne (but get little red dot artifacts all over the screen) but 3dmark2000 and 2001 both crash to desktop or lock. Please help me I want use this card. What I dont understand is that I have a Matrox G550 before and could run my system at 140x10.0=1400mhz and agp4x and no problems
Ok its almost like the card is overheating but when i touch the heatsink on the card its cool. After running 3dmark2000 for about a minute I stat getting little artifacts all over the screen. and then i get kicked to the desktop and my whole screen gets distorted. Now i am at 1333 mhz right now. it makes no sense that the card is so wimpy that I have to run my t-bird at stock 1 gig, and every other card I have ever used I could run it at 1.4 (140x10) any ideas
Participate on our website and join the conversation
This topic is archived. New comments cannot be posted and votes cannot be cast.
Responses to this topic
to me it soundsl ike a bad card my one geforce 2 mx did the same thing except is was pci
this is a long shot, but try this utility.
Radeon Tweaker
This may be able to help you out until you can get another card.
I'm sorry to say it sounds like a bad card to me as well.
I know that ATI's OEM cards use slower ram, and a slweor clock speed. Usually ATI's cards (I have a radeon 64 meg DDR) and it runs GREAT overclocked by 30 MHz.
Radeon Tweaker
This may be able to help you out until you can get another card.
I'm sorry to say it sounds like a bad card to me as well.
I know that ATI's OEM cards use slower ram, and a slweor clock speed. Usually ATI's cards (I have a radeon 64 meg DDR) and it runs GREAT overclocked by 30 MHz.
Crazy take a look at these posts and it will give you more info
ok check my posts out and you will understand
http://www.rage3d.com/board/showthread.php?s=&threadid=33594629
http://www.rage3d.com/board/showthread.php?s=&threadid=33594456
ok check my posts out and you will understand
http://www.rage3d.com/board/showthread.php?s=&threadid=33594629
http://www.rage3d.com/board/showthread.php?s=&threadid=33594456