harddrive locked in PIO mode
i appologize about the other post, im new here, and didnt realize what topic i wuz on my primary drive recently went into PIO mode, and i wuz wondering if ne one knows if its possible by software, or some other means, 2 take it out of PIO mode.
i appologize about the other post, im new here, and didnt realize what topic i wuz on
my primary drive recently went into PIO mode, and i wuz wondering if ne one knows if its possible by software, or some other means, 2 take it out of PIO mode. it wuz my fault, and it may b damaged. i wuznt paying attention and my elbow slammed into it, hard, hard enough 2 freeze it, and knocked it into PIO mode. it wuz running dma mode 5, but is now in PIO. its a western digital 80 gig special edition, IDE version. ive already ordered a new drive, same drive except its a sata version, and im hoping 2 b able 2 ghost it. id still like 2 use this drive for storage, but its kinda useless in PIO mode. ne help would b appciated.
my primary drive recently went into PIO mode, and i wuz wondering if ne one knows if its possible by software, or some other means, 2 take it out of PIO mode. it wuz my fault, and it may b damaged. i wuznt paying attention and my elbow slammed into it, hard, hard enough 2 freeze it, and knocked it into PIO mode. it wuz running dma mode 5, but is now in PIO. its a western digital 80 gig special edition, IDE version. ive already ordered a new drive, same drive except its a sata version, and im hoping 2 b able 2 ghost it. id still like 2 use this drive for storage, but its kinda useless in PIO mode. ne help would b appciated.
Participate on our website and join the conversation
This topic is archived. New comments cannot be posted and votes cannot be cast.
Responses to this topic
Quote:
http://www.michna.com/kb/WxDMA.htm
1. Uninstall the secondary IDE port
To do that, open Device Manager as follows. Right-click on My Computer, select Properties, click on the Hardware tag, click on the Device Manager button, click on the plus sign to the left of IDE ATA/ATAPI Controller, right-click on Secondary IDE Channel, click on Uninstall. Deactivating is not enough.
Reboot to make the changes active and permanent.
After booting Windows will automatically reinstall the IDE channel and the DVD (or CD) drive. This Plug-n-Play process can take a little while, so give it a minute after the boot process finishes.
2. Reactivate DMA
But this is not enough, because unfortunately Windows does not automatically activate DMA on a DVD or CD drive. You have to tell Windows to try to use DMA first.
For that, go to Device Manager again. Right-click on My Computer, select Properties, click on the Hardware tag, click on the Device Manager button, click on the plus sign to the left of IDE ATA/ATAPI Controller, double-click on the secondary IDE channel, click on Extended Settings and change the relevant setting from PIO only to DMA when available.
On Windows NT and 2000 you now have to reboot a second time, but Windows XP applies the change instantly. Then you can go to the same place in Device Manager again and check whether the device is now actually using DMA mode. If so, all is well.
http://www.michna.com/kb/WxDMA.htm
1. Uninstall the secondary IDE port
To do that, open Device Manager as follows. Right-click on My Computer, select Properties, click on the Hardware tag, click on the Device Manager button, click on the plus sign to the left of IDE ATA/ATAPI Controller, right-click on Secondary IDE Channel, click on Uninstall. Deactivating is not enough.
Reboot to make the changes active and permanent.
After booting Windows will automatically reinstall the IDE channel and the DVD (or CD) drive. This Plug-n-Play process can take a little while, so give it a minute after the boot process finishes.
2. Reactivate DMA
But this is not enough, because unfortunately Windows does not automatically activate DMA on a DVD or CD drive. You have to tell Windows to try to use DMA first.
For that, go to Device Manager again. Right-click on My Computer, select Properties, click on the Hardware tag, click on the Device Manager button, click on the plus sign to the left of IDE ATA/ATAPI Controller, double-click on the secondary IDE channel, click on Extended Settings and change the relevant setting from PIO only to DMA when available.
On Windows NT and 2000 you now have to reboot a second time, but Windows XP applies the change instantly. Then you can go to the same place in Device Manager again and check whether the device is now actually using DMA mode. If so, all is well.
